Showing 17–32 of 153 results
The 5-step block is used to calibrate thickness and linearity. The steps are 0.500″, 0.400″, 0.300″, 0.200″ and 0.100″ thick, and each step face measures 0.750 “x0.750”. The block is manufactured in accordance with ASTM E797. If needed, we offer customization for additional and larger steps.
Features
The 5-step block is used to calibrate thickness and linearity. The steps are 0.500″, 0.400″, 0.300″, 0.200″ and 0.100″ thick and each step face measures 0.750 “x0.750”. The block is manufactured in accordance with ASTM E797. If needed, we offer customization for additional and larger steps.
Features
El bloque de 5 escalones se utiliza para la calibración de espesor y linealidad. Los escalones tienen un grosor de 2,5 mm, 5,0 mm, 7,5 mm, 10,0 mm y 12,5 mm, y cada cara del escalón mide 20 mm x 20 mm. El bloque se fabrica de acuerdo con la norma ASTM E797. Si es necesario, ofrecemos la posibilidad de personalizarlo para escalones adicionales y de mayor tamaño.
UT 5-STEP CALIBRATION BLOCK.
The 5-step block is used for thickness and linearity calibration. The steps are 2.0 mm, 4.0 mm, 6.0 mm, 8.0 mm and 10.0 mm thick, and each step face measures 20 mm x 20 mm. The block is manufactured in accordance with ASTM E797. If required, we offer customization for additional and larger step sizes.
Features:
The 5-step block is used to calibrate thickness and linearity. The steps are 2.0 mm, 4.0 mm, 6.0 mm, 8.0 mm and 10.0 mm thick, and each step face measures 20 mm x 20 mm. The block is manufactured in accordance with ASTM E797. If required, we offer customization for additional and larger step sizes.
Features
The 5-step block is used to calibrate thickness and linearity. The steps are 2.0 mm, 4.0 mm, 6.0 mm, 8.0 mm and 10.0 mm thick, and each step face measures 20 mm x 20 mm. The block is manufactured in accordance with ASTM E797. If required, we offer customization for additional and larger step sizes.
Features
As a leading solution for corrosion assessments and precise thickness measurements, the Sonatest AlphaGage+ instrument employs advanced technologies tailored to different industry needs.
Ultrasonic touch probes.
Ultrasonic transducers with angled beams are recommended for parts with inclined defects, such as welds, and are sometimes used in mechanized or automated testing. They use refraction to transmit shear or longitudinal waves at a predetermined angle, whereas most standard transducers generate shear waves by mode conversion. The elements are mounted in integral or replaceable pads that require a coupling layer, usually gel, oil or paste.
Our angle beam probes are available in single and dual element configurations and in a variety of sizes.
ASME SEC V UT CALIBRATION BLOCK (3/4” THICK)
The Asme Sec V ¾ block is used for obtaining primary reference responses in ultrasonic inspection of primary reference welds in ultrasonic inspection of welds. The calibration block is manufactured with 1 laterally drilled hole on one face (at 3/32“ diameter, 1.75” deep, located through the thickness at 1/2T), 2 laterally drilled holes on the opposite face (at 3/32“ diameter, 1.75” deep, located through the thickness at ¼ and 3/4T), 2 EDM notches on the top and bottom faces, both sized 2%T deep x 1/8“ wide x 1-3/8” long.
Customization available if required for notches and holes. Reference block is manufactured in accordance with ASME Sec V Art 4 Fig. T-434.2.1.
Features
Dimensions: 0.75“ (H) X 6.25” (L) X 6.0” (W)
Weight: 7.985 LBS
Material: 1018 STEEL, NICKEL PLATED
Specifications: ASME SEC V, ART 4, FIG. T-434.2.1
ASME SEC V UT CALIBRATION BLOCK (1-1/2″ THICK)
The Asme Sec V 1-1/2 block is used to obtain primary reference responses in ultrasonic inspection of primary reference welds in ultrasonic inspection of welds. The calibration block is manufactured with 1 laterally drilled hole on one face (at 1/8″ diameter, 1.75″ depth, located through the thickness at 1/2T), 2 laterally drilled holes on the opposite face (at 1/8″ diameter, 1.75″ depth, located through the thickness at ¼ and 3/4T), 2 EDM notches on the top and bottom faces, both sized 2%T deep x 1/8″ wide x 1-3/8″ long. Customization available if required for notches and holes. Reference block is manufactured in accordance with ASME Sec V Art 4 Fig. T-434.2.1.
Features
BLOQUE DE CALIBRACIÓN ASME SEC V UT (3/4″ DE ESPESOR)
El bloque Asme Sec V ¾ se utiliza para la obtención de respuestas de referencia primarias en la inspección ultrasónica de soldaduras. El bloque de calibración está hecho con 1 orificio perforado lateralmente en una cara (a 3/32″ de diámetro, 1,75″ de profundidad, situado a través del espesor a 1/2T), 2 orificios perforados lateralmente en la cara opuesta (a 3/32″ de diámetro, 1. 75″ de profundidad, situados a través del espesor a ¼ y 3/4T), 2 muescas EDM en las caras superior e inferior, ambas dimensionadas a 2%T de profundidad x 1/8″ de ancho x 1-3/8″ de largo.
Personalización disponible si es necesario para muescas y orificios. El bloque de referencia se fabrica de acuerdo con ASME Sec V Art. 4 Fig. T-434.2.1.
Características
Dimensiones: 0.75″ (H) X 6.25″ (L) X 6.0″ (W)
Peso: 8.117 LBS
Material: ACERO INOXIDABLE 304
Especificaciones: ASME SEC V, ART 4, FIG. T-434.2.1
ASME SEC V UT CALIBRATION BLOCK (1-1/2″ THICK)
The Asme Sec V 1-1/2 block is used to obtain primary reference responses in ultrasonic inspection of primary reference welds in ultrasonic inspection of welds. The calibration block is manufactured with 1 laterally drilled hole on one face (at 1/8″ diameter, 1.75″ depth, located through the thickness at 1/2T), 2 laterally drilled holes on the opposite face (at 1/8″ diameter, 1.75″ depth, located through the thickness at ¼ and 3/4T), 2 EDM notches on the top and bottom faces, both sized 2%T deep x 1/8″ wide x 1-3/8″ long. Customization available if required for notches and holes. Reference block is manufactured in accordance with ASME Sec V Art 4 Fig. T-434.2.1.
Features
ASME SEC V UT CALIBRATION BLOCK (3/4″ THICK)
The Asme Sec V ¾ block is used for obtaining primary reference responses in ultrasonic inspection of welds. The calibration block is made with 1 laterally drilled hole on one face (at 3/32″ diameter, 1.75″ deep, located through the thickness at 1/2T), 2 laterally drilled holes on the opposite face (at 3/32″ diameter, 1. 75″ deep, located through the thickness at ¼ and 3/4T), 2 EDM notches on the top and bottom faces, both sized at 2%T deep x 1/8″ wide x 1-3/8″ long.
Customization available if needed for notches and holes. Reference block is manufactured in accordance with ASME Sec V Art 4 Fig. T-434.2.1.
Features
ASME SEC V UT Calibration Block (1-1/2″ thick).
The Asme Sec V 1-1/2 block is used for obtaining primary reference responses in ultrasonic inspection of welds.
The calibration block is manufactured with 1 laterally drilled hole on one face (at 1/8″ diameter, 1.75″ deep, located through the thickness at 1/2T), 2 laterally drilled holes on the opposite face (at 1/8″ diameter, 1.75″ deep, located through the thickness at ¼ & 3/4T), 2 EDM notches on the top and bottom faces, both sized at 2″ deep x 1/” wide x 1-3/8″ long.
Customization available if required for notches and holes. Reference block is manufactured in accordance with ASME Sec V Art 4 Fig. T-434.2.1.
Features
BLOQUE DE CALIBRACIÓN ASME SEC V UT (3/4″ DE ESPESOR)
El bloque Asme Sec V ¾ se utiliza para la obtención de respuestas de referencia primarias en la inspección ultrasónica de soldaduras. El bloque de calibración está hecho con 1 orificio perforado lateralmente en una cara (a 3/32″ de diámetro, 1,75″ de profundidad, situado a través del espesor a 1/2T), 2 orificios perforados lateralmente en la cara opuesta (a 3/32″ de diámetro, 1. 75″ de profundidad, situados a través del espesor a ¼ y 3/4T), 2 muescas EDM en las caras superior e inferior, ambas dimensionadas a 2%T de profundidad x 1/8″ de ancho x 1-3/8″ de largo.
Personalización disponible si es necesario para muescas y orificios. El bloque de referencia se fabrica de acuerdo con ASME Sec V Art. 4 Fig. T-434.2.1.
Características
Dimensiones: 0.75″ (H) X 6.25″ (L) X 6.0″ (W)
Peso: 8.117 LBS
Material: 7075-T6 ALUMINUM
Especificaciones: ASME SEC V, ART 4, FIG. T-434.2.1
ASME SEC V UT CALIBRATION BLOCK (1-1/2″ THICK)
The Asme Sec V 1-1/2 block is used for obtaining primary reference responses in ultrasonic inspection of welds. The calibration block is manufactured with 1 side drilled hole on one face (at 1/8″ diameter, 1.75″ deep, located through the thickness at 1/2T), 2 side drilled holes on the opposite face (at 1/8″ diameter, 1.75″ deep, located through the thickness at ¼ & 3/4T), 2 EDM notches on the top and bottom faces, both sized at 2%T deep x 1/8″ wide x 1-3/8″ long.
Customization available if required for notches and holes. Reference block is manufactured in accordance with ASME Sec V Art 4 Fig. T-434.2.1.
Features