Showing 33–48 of 52 results
The MD-Series multi-directional magnetic bench offers Alternating Current, Half Wave Direct Current and 1-phase Full Wave Direct Current for time-saving multidirectional magnetization which can find defects in all orientations with one mag-cycle.
This line of mag particle testing meters will help you check and measure the performance of your magnetic bench, electromagnetic current generator or other magnetizing equipment as part of your regular system performance checks.
Find out more about each of our mag particle testing meters by clicking on the tabs below, or contact us for help choosing the right field indicator for your application.
MG-410 is an ultra-bright fluorescent magnetic particle powder for locating small, medium, and large discontinuities. These particles provide clear, ultra-bright, fluorescent green indications under UV light with minimal background. MG-410 is designed for use in water or oil baths for wet method fluorescent magnetic particle testing.
MG-450A is a borax-free ultra-high fluorescence magnetic particle premix for locating small, medium and gross discontinuities in high-volume applications using wet method magnetic particle testing.
Designed to mix with water, MG-450A improves indication visibility with less background fluorescence because of the high-strength, high-fluorescent MG-410 particles.
A highly-sensitive water-based magnetic particle fluid for non-fluorescent (visible) wet method magnetic particle testing to locate fine and medium discontinuities on finished parts. MV-740 provides clear, strong indications due to the heavy buildup of the highly magnetic particles. The product is ready-to-use, so no dilution is required.
MV-740 is often used with WCP-2 white contrast paint to improve contrast and inspection sensitivity.
The Visible Light Meter accurately measures visible light in both foot-candles per and lux and includes a permanently attached visible light sensor, specially designed to measure visible white light in the 400-760 nm range for non-destructive testing.
These handheld electrodes and contact clamps are convenient for conducting sectional magnetic particle inspections, like welds, castings or forgings, or testing parts that cannot be inspected on a wet horizontal bench, such as large fabrications, tubing, bars and tubular assemblies like aircraft mounts and fuselage sections.
Magnaflux understands some parts will not lend themselves to traditional units. Some of these parts are too large, some need special handling, and some are better processed dry. The CSV-Series offers a solution to the parts that are too large for normal systems.
Magnaflux demagnetization units remove residual magnetism remaining after conducting Magnetic Particle Inspection. The upgraded design allows users to run the coil continuously, without a duty cycle cool down period or a hot coil.
The Universal WE magnetic wet bench is multi-direction magnetic wet bench designed to completely magnetize the surfaceof parts up to 35 inches long in a single shot. Potentially cutting inspection time in half because the part can inspected in both directions at once. The Universal WE offers 200 – 2,000 Amps AC for contact shots and 1,500 – 15,000 Amp-turns AC for coil shots. The two outputs are independently adjustable to set each magnetic field, circular or longitudinal.
WA-2B is a general-purpose water-conditioning powder to enhance surface wetting and magnetic particle dispersion stability in water-based magnetic particle suspensions. Its unique blend of wetting agents, corrosion inhibitors and anti-forming agents eliminates the need for additional water conditioning agents.
A white granular powder that is added to water baths in wet method magnetic particle testing with no further bath treatment required. WA-2B features good surface wetting and particle dispersion, and will not cake in storage. WA-2B is added to the water bath and stirred until dissolved before the magnetic particles are added.
A bright white, opaque NDT contrast paint, WCP-2 provides a high contrast background to improve probability of detection and sensitivity during visible magnetic particle inspections.
This fast drying paint aerosol sprays on evenly, without flaking, before inspection so when non-florescent / colored magnetic particles are applied, the indications appear clearly against the opaque white background.
WCP-2 can be used with all types of colored and visible mag particles, including 7HF or 7C Black wet method particles, and #2 Yellow or #8A Red dry method magnetic powders.
The Y-2 is an AC electromagnetic yoke, ergonomically designed to improve productivity and reduce operator arm and wrist fatigue. The yoke generates a strong AC magnetic field for the detection of surface indications during magnetic particle testing.
The Y-7 is a durable, high-strength AC/DC magnetic yoke designed to detect surface and sub-surface indications in the most rugged applications.
Featuring sealed chemical-resistant construction, articulating legs to contour to any part shape and robust strain-relieved twelve-foot cord for field use, the Y-7 is ideal for inspection of welds and other remote testing.